DPA 2028 Supercardiod Vocal Mic, SL1 Adapter

DPA 2028 Supercardiod Vocal Mic, SL1 Adapter

DPA  2028 Supercardiod Vocal Mic, SL1 Adapter

DPA 2028 Supercardiod Vocal Mic, SL1 Adapter

DPA Microphones 2028 Supercardiod Vocal Mic, SL1 Adapter (Shure/Sony/Lectrosonics), Black

SKU: DPA-2028-B-SL1
MSRP: $600.00
MAP: $600.00

Overview

 DPA's industry-leading speech and vocal reproduction come to your very own wireless handheld in the 2028 supercardioid microphone capsule — compatible with select wireless systems from Shure, Sony, and Lectrosonics. Crooners to screamers, slam poets to beatboxers, the 2028 is built to deliver 1:1 vocal reproduction of virtually any vocal performer. DPA's famously flat off-axis response gives the 2028 extremely natural sonics and a consistent pickup, even in the hands of dynamic singers. What's more, a supercardioid pickup pattern equips the 2028 with maximum gain before feedback and exemplary isolation, allowing you to get more of your voice — and not the rest of your band — in your wedges and ears. We at Sweetwater found the three-stage shockmount, pop filter, and grille to be extremely effective at reducing handling noise and plosives into the mic, eliminating distracting artifacts and overs from ruining performances. If you've been searching for DPA vocal performance from a drop-in wireless capsule, the 2028 is definitely worth a look.

Features

  • Premier DPA vocal reproduction

  • Suited to all types of singers, speakers, and vocalists

  • Flat off-axis response yields consistent pickup from dynamic singers

  • Supercardioid polar pattern maximizes isolation and gain before feedback

  • Three-stage shockmount/filter/grille neutralizes handling noise and plosives

  • SL1 capsule type is compatible with select wireless mics from Shure, Sony, and Lectrosonics

Specifications

  • Directional pattern
  • Supercardioid
  • Principle of operation
  • Pressure gradient
  • Cartridge type
  • Pre-polarized condenser
  • Effective frequency response
  • 20 Hz - 20 kHz
  • Frequency range, ±2 dB, at 12 cm (4.7 in)
  • 100 Hz - 16 kHz. Permanent 3rd order low-cut filter at 80 Hz
  • Sensitivity, nominal, ±3 dB at 1 kHz
  • 5 mV/Pa; -46 dB re. 1 V/Pa
  • Equivalent noise level, A-weighted
  • Typ. 22 dB(A) re. 20 µPa (max. 23 dB(A))
  • Total harmonic distortion (THD)
  • < 1% up to 139 dB SPL peak
  • Dynamic range
  • Typ. 117 dB
  • Max. SPL, peak before clipping
  • 160 dB
  • Output impedance
  • 150 Ω
  • Minimum load impedance
  • 1 kΩ
  • Cable drive capability
  • 100 m (328 ft)
  • Output balance principle
  • Impedance balancing with Active Drive
  • Common mode rejection ratio (CMRR)
  • > 50 dB at 1 kHz
  • Power supply (for full performance)
  • 48 V Phantom power (±4 V)
  • Current consumption
  • Max 2.5 mA
  • Connector
  • XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
  • Weight
  • 286 g (10.1 oz)
  • Diameter
  • 48 mm (1.9 in)
  • Capsule diameter
  • 19 mm (0.75 in)
  • Microphone length
  • 188 mm (7.4 in)
  • Maximum output voltage, RMS
  • 9 Vrms; 19 dBV; 28 dBu
  • Polarity
  • +V at pin 2 for positive sound pressure